Â
Â
- Yokohama type fender net type
- Sling pneumatic rubber fender
- Ribbed pneumatic rubber fender
Floating pneumatic rubber fender, Yokohama fender, ship airbags,Super cell fenders (SC type), Cone fenders, Super Arch fenders (type SA), Cylindrecal fenders (Type Y), Semi-circular fenders (Type D), Type GD fenders, Type I fenders, Type U fenders,Turn cell fenders, Type π rubber fenders, Rubber ladder, Rubber fenders for tug boats, PVC yacht fenders etc.
 Mearsk , MSC, COSCO, CMACGM, OOCL, APL, NYK , NEW YORK port, KOBE port, YOKOHAMA port, Singapore port, ANTWERP port, LONDON port, HAMBURG port, DUBAI port, QINGDAO port, SHANGHAI port etc.
2.Product description:
Penumatic rubber fender with chain protection
(1) High energy absorption
The amount of energy absorbed is the main technical performance indicators fender instruments. With the ship's tonnage growth, berthing operations, ship collision energy contact quay or other ships also doubled. Huge collision energy must rely on the contact area on the fender and enough to absorb sufficient deformation. Our ship fender use compressed air as the buffer medium to absorb ship impact energy and have good elasticity.
(2) Ultra low back pressure
The inside air of  pneumatic fenders is low pressure gas, the internal pressure increase is very limited during compression deformation. Due to the large contact area, unit pressure acting on the ship hull surface is very low, compared with other fender instruments, is not the common low back pressure.
(3) Inclined contact, good adaptability
Ship must have certain angle which have the possibility of contacting the side of the shore. As the inclined interface of sea inflatable fender, its adaptability is much higher than other fender.
Â
(4)Floating performance is good, not subject to tidal influence, fender can be maintained in the ideal level
Â
Pneumatic fenders floating on the water surface (more than 50% of the volume), along with the change of position is not relative to the tidal fluctuation. Especially the ship as the waves rolling, cylindrical inflatable fenders with rolling, the friction force is very small. So it will not damage the coating surface of the hull, and also decrease the moving.
 Fender performance specification  Â
Â
Size | Initial internal pressure |
Guaranteed energy absorption                  GEA(kJ) |
Reaction force at GEA deflection                        R((kN)) |
D×L(m) | (Kpa) |
Minimum value at deflection 60±5% |
Tolerance ±10% |
0.5×1.0 | 50 | 6 | 64 |
0.6×1.0 | 50 | 8 | 74 |
0.7×1.5 | 50 | 17 | 137 |
1.0×1.5 | 50 | 32 | 182 |
1.0×2.0 | 50 | 45 | 257 |
1.2×2.0 | 50 | 63 | 297 |
1.35×2.5 | 50 | 102 | 427 |
1.5×3.0 | 50 | 153 | 597 |
1.7×3.0 | 50 | 191 | 639 |
2.0×3.5 | 50 | 308 | 875 |
2.5×4.0 | 50 | 663 | 1381 |
2.5×5.5 | 50 | 943 | 2019 |
3.0×5.0 | 50 | 1210 | 2104 |
3.0×6.0 | 50 | 1485 | 2583 |
3.3×4.5 | 50 | 1175 | 1884 |
3.3×6.0 | 50 | 1675 | 2783 |
3.3×6.5 | 50 | 1814 | 3015 |
3.3×10.6 | 50 | 3067 | 5257 |
4.5×9.0 | 50 | 4752 | 5747 |
4.5×12.0 | 50 | 6473 | 7984 |
Brief introduction and editing of dust remover
Bag Filter [1] is a dry dust filter. After a period of use of filter material, due to the effect of sieve filtration, collision, retention, diffusion, static electricity and so on, the surface area of the filter bag is gathered in a layer of dust. This layer of dust is called the initial layer. In the course of the movement, the primary layer becomes the main filter layer of the filter material, and the larger filter material of the net hole can also get higher filtration depending on the effect of the initial layer. Efficiency. With the accumulation of dust on the surface of the filter material, the efficiency and resistance of the Dust Collector all increase correspondingly. When the pressure difference on both sides of the filter material is very large, some fine particles that have been attached to the filter material will be squeezed past to reduce the efficiency of the dust collector. In addition, the high resistance of the dust collector will reduce the air volume of the dust removal system significantly. Therefore, when the resistance of the dust collector reaches a certain value, the ash should be cleaned in time. When cleaning, the primary layer should not be destroyed, so that the efficiency will be reduced.
Flat Bag Dust Collector,Portable Dust Collector,Washable Dust Collector,Mobile Welding Smoke Collector
Botou Youjian Environmental Protection Equipment Co. LTD. , http://www.btdustmachine.com